How to install the floor heating price how to install warmer warmer

When installing the floor heating, it must be operated according to the specification, so as to ensure the heating effect and service life of the floor heating. What is the price for installing a floor heating ? How to install a warmer warmer? Let's take a look with Xiao Bian!

What is the installed floor heating price:

The installation of floor heating prices is not uniform and will be affected by the installation costs of floor heating coils, floor heating boilers, cement screeds, platoons, and manifolds. The installation cost of floor heating is generally about 40 to 80 yuan, cement is leveled at about 60 yuan per square meter, and the cost of separate water collectors is generally about 500 yuan. The cost of installing the floor heating boiler is generally 300 to 600 yuan, and the cost of the cable is generally several hundred. Yuan around.

How to install warmer warmer:

1, to first find a good installation team, and then to the market to understand the warm material, good team + good material to create a good warmth.

2. Before installation, some geothermal pipes should be wrapped with insulation cotton and then laid. This can ensure the circulation of hot water in the pipes, so that the temperature of each room is more warm and balanced.

3, in the installation, the floor heating switch should be put on the insulation cotton, so that has the effect of insulation, can avoid hot water before entering the room cooling.

4. Before laying the thermal insulation layer, first lay a layer of moisture-proof layer on the ground, and after completion, lay the insulation board reflective film and steel wire mesh. Then lay the insulating layer on the leveling layer and glue the board to the seam. Lay aluminum foil or stick a layer of composite aluminized polyester film on the floor heating insulation layer. After the insulation layer is laid flat, a reflective film is laid to prevent heat loss. Finally, a layer of protective film is applied on the reflective film of aluminum foil, which allows the temperature to radiate upwards, reducing the loss of conduction down the temperature.

Warm installation precautions:

1, in the industry there are "three points of the floor, seven installations," saying that the importance of the installation team, only a good installation team can create a good floor heating.

2. Check the sealing of the floor heating system before installation.

3, in the installation, the ground should be dry and dry, the ground moisture content can not be higher than 1.5%; indoor humidity can not be too large, it is best to control at 60 degrees.

4, in the installation, the floor and the wall to set aside the gap, and use a thicker skirting board.

5. The installation of the floor and the skirting board should be performed in two separate steps. After the installation of the floor is completed, wait 48 hours. After the glue is dry, remove the fastener and then do the skirting board.

6, the floor to be installed 24 hours before heating.

The article concludes: How much is the installed floor heating price and how to install the warmer and warmer knowledge is introduced here, and for those who need to know more information, please continue to pay attention to this site and we will have more exciting content.

Yangzhou Chengde have the certification of API 5L and API 5CT, so we permit to produce and sell the API pipes with the Chengde brand directly.

We can produce the API pipes according to the API 5L standard, such as the GR.B Steel Pipe, X42 steel pipe, X52 steel pipe, X65 steel pipe, X70 steel pipe, X80 steel pipe, etc.

The follow table is our main reference list on the API 5L product

 

Customer

PJT name

Grade and size range

Quantity(MT)

Keppel

N/A

X52/X65 PSL2 OD (244.5~457)x(12.7~38.1) mm

3650

Shell

NYHAMNA

X52/GR6/X52 PSL2 OD (219~609)x(12.7~65) mm

968

SBM

SAXI BATUQUE

X52/X65 PSL2 OD (219~660)x(25.4~70) mm

1100

Exxon Mobil

Oil Field Chayvo

X60PSL2/GR.6 OD(273.1~609.6)x(15.09~76.2)

310

Dalian Shipping Building/ZPMC

Leg bracing pipe

X52~X80 PSL2

OD (159~955) x(10~51)mm

7050

PETROBRAS

PMXL1 MEXILHAO

X52/X60/X65 PSL2 OD (219~762)x(18.3~69.85)mm

850

 

The Piercing and rolling technology of Chengde possesses a number of patents in designing and manufacturing the equipment, and has improved in lots of areas targeting better performance and efficiency, which has distinguished itself from the peers. 

Advantages of our pipes

1        Uniform mechanical properties and dimensions in longitudinal& transversal directions and better surface condition

2  Minimum Order Quantity (MOQ) as low as ONE piece AND Huge size scope to accommodate the project requirements (8"~48``).

3  Competitive price and shorter delivery, Superior international standard quality.

4  30 years experience and approvals with Major EPCs/OEMs/Clients in the supplier chain.

API 5L 5CT Certification


API 5L Pipe

Line Pipe,Api 5L Pipe,X52 Pipe,X65 Pipe

YANGZHOU CHENGDE STEEL PIPE CO.,LTD , https://www.chengdepipe.com